Material

Stainless steel

Everything in the catalogue the supplier states is made in stainless steel.

9 products

In the catalogue

Triangular corner floor drain for a shower or wet-room corner

Corner Drain

Triangular floor drain for a corner installation — shower corners and other wet-room corners where a square or round drain does not fit. Stainless steel (SUS304), 0.8mm base / 1.2mm cover. 19.5×19.5×27.5cm triangle, vertical outlet spigot. Plain or chevron-pattern cover, in brushed silver or black.

Round floor drain with a hinged flap for backflow protection

Flap Floor Drain

Round floor drain with a spring-hinged flap beneath the grate, closing against backflow and odour when not draining. Stainless steel, 3mm gauge, bright or sanded finish. 120mm (65mm outlet) with a petal-slot grate, and 150mm (65/80mm outlet) with an oval-slot grate.

Flush hidden-cover linear drain fitted between two floor tiles

Linear Drain — Tile Insert

Flush linear channel drain, the cover sitting level with the floor with no visible grate — either a plain flush panel or, on one finish, a decorative laminate insert. Stainless steel (SUS304/SUS201) body and cover, 1.2-2mm gauge depending on finish. Silver, gold, black and mirror finishes; widths from 6-8cm, lengths from 20-100cm depending on finish. Outlet is a single vertical spigot beneath the channel.

Linear floor drain with a visible perforated grate pattern

Linear Drain — Visible Grate

Linear channel drain with a visible perforated cover — slotted, punched-oval or pattern-cut, in stainless steel (SUS304/SUS201). Widths from 3.2-10cm, lengths from 20-100cm depending on pattern. Matte silver, black, gold and mirror finishes; some patterns take a configurable outlet position with a 360-degree rotation port, and one width range ships with adjustable levelling feet. Fourteen grate patterns.

Shattaf Valve

Wall-mounted body combining the water connection, a ceramic on-off valve and the hand-shower holder. Chrome-plated brass or stainless steel. Four configurations: concealed 3-in-1 for bidet or shower (6039-00); concealed 4-in-1 adding a second outlet and a ball service valve for flush-tank connection (6045-00); concealed 4-in-1 for instant heaters, which then connect to electricity only (6046-00); and pre-wall 3-in-1 for mounting before tiling (6052-00). Each in chrome, stainless steel and matte black. Water is opened and closed by pushing or pulling the hand shower; manufacturer's stated saving of up to 40% on heated water. Registered design, European registration 015068066; design applications filed in China and Southeast Asia.

Square floor drain with a decorative perforated grate

Square Drain — Decorative Grate

Square floor drain with a visible decorative grate — geometric, diagonal, maze or wave patterns cut into a stainless steel (SUS304/SUS201) cover, 0.8-6mm gauge depending on pattern. Sizes mostly 10×10cm, with several patterns also available at 15×15cm and 20×20cm. Silver, black, gold and mirror finishes; outlet is a vertical spigot, a side outlet, or on one pattern an angled chrome elbow fitting. Twenty-three grate patterns.

Flush square floor drain designed to take an inset tile

Square Drain — Tile Insert

Square floor drain with a flush or recessed tray cover, level with the floor, some designed to take an inset tile so the cover disappears into the floor pattern. Stainless steel (SUS304/SUS201), 0.8-1.2mm gauge. Sizes 10×10cm to 20×20cm depending on finish; one size ships with a side outlet rather than a vertical spigot.

Double-bowl stainless steel sink with rounded ends, shown from above

Stainless Steel Kitchen Sink

Stainless steel kitchen sinks in nine series, shown below: pressed round, single, double and drainboard sinks, undermount bowls, square-cornered handmade sinks in brushed steel, black and gold, sinks on open stands, round vessel bowls, and workstation sinks with a built-in cutting board and colander. Each series is a model card; every model is listed with its own size, and the model and size are confirmed per order. Wastes, overflow pipes, baskets, soap dispensers and cutting boards to match are available on request.

L-shaped floor drain fitted into the corner where floor meets wall

Wall L Floor Drain

L-shaped floor drain for the corner where the floor meets the wall, with a slotted grate on both the floor and wall faces. Stainless steel (SUS304), 2mm gauge, wire-drawn finish. Two sizes: 100mm with a 75mm outlet spigot, and 120mm with an 85mm outlet spigot.

All products

Other materials

Or browse

Wood-plastic composite (WPC)Stone-plastic composite (SPC)PVC MDF Polystyrene (PS)Sintered stone Aluminium Brass

Tell us the space and the quantity.

Send the room, the area in square metres and your target date. You will get specifications, lead time and a price — or a plain answer about what is not yet known.

Start an enquiry

Your enquiry list is full at 30 products. Send this enquiry, or remove something, before adding more.